Class Type:	Programming								


System:		Alpha/Delta 1000								


Duration:		2.5 Days									


Class Audience:	Operators of Delta 1000 systems and/or maintenance personnel 			
		for the Delta1000 System Distributed HVAC Hardware Modules(DGP's)																														


Objectives:	Upon completion of the course the student will be able to:			


  		Describe the D1000 system hardware components and draw a D1000 system block diagram. 												
  		Perform all System Initialization Function codes									
  		Perform all DGP Programming Function Codes										
  		Perform all Peripheral Programming Functions codes									
  		Patrol Tour Programming Function Codes										
  		Time and Event Programming Function codes										

	
Topics:		D1000 system hardware/software/firmware overview					
  		Level 1 Function Codes 												
		Level 2 Function Codes									      							

	

Class Type:	Programming								


System:		Alpha/Delta 1000								


Duration:		3.0 Days									


Class Audience:	Operators of Delta 1000 systems and/or maintenance personnel 				
		for the Delta1000 System Distributed HVAC Hardware Modules (DGP's)													


							
Objectives:	Upon completion of the course the student will be able to:				
		Describe the D1000 Control Interpreter Language Utility 						
  		Describe the D1000 CIL Data Entry Format and Procedures						
  		Write, enter and test the Pump Rotation Program								
  		Write, enter and test the Enthalpy Program								
  		Write, enter and test all Start/Stop Programs designed for the class														
  		Write, enter and test all Date and Time-Initiated Programs							



Topics:	    	D1000 system hardware/software/firmware overview				
  	         The D1000 Control Interpreter Language Fundamentals 				
  	         D1000 Control Interpreter Language Data Entry					
  		CIL Program Test and Checkout Procedures 												

Class Type:	Programming									


System:		Excel/Excel Microcentral							

											
Duration:		4.5 Days									


Class Audience:	Programmers of down-line Excel processors and/or maintenance 			
		personnel for the Excel Controllers in Excel Microcentral or 					
		Distributed Excel HVAC Systems																


Objectives:	Upon completion of the course the student will be able to:			


  		Identify the Point and Program of an Excel Controller database							
  		Understand the nature and significance of an HVAC Control Loop							
  		Flow-chart an HVAC Control Loop using RACL Standard Programming Symbology															
  		Write RACL program code to implement a flowchart for an HVAC Control Loop															
  		Use System Commands to execute written program code											
  		Test/checkout a completed program for correct on-line operation								
 		Use all RACL HVAC-related Operators to write error-free and easily understood programs																
  		Create Custom Submodules and use them in the Main Module M0									
  		Save and Load Controller Program and Point databases to tape								

Topics:		Excel/Excel Microcentral System Block Diagram				
		Controller Point and Program files							
		DDC control loops												
		RACL flowchart form											
		Main Module M0												
		RACL statement flowchart											
		Introduction to Standard Submodules									
		Creating a Custom submodules										
		Creating a Datafile											
		Completing A RACL flowchart										
		Complete RACL Instruction Set										
		Deciphering System Documentation									

Class Type:	Basic Operation 											

	
System:		Microcentral											


Duration:		4.5 Days													


Class Audience:	Maintenance Personnel responsible for operating the Excel Plus 								
		System with a PC and a Bus Interface																														


Objectives: 	Upon completion of the course the student will be able to:							


  		Identify Excel Plus Microcentral System Hardware including the Peer Bus													
  		Identify software/firmware in all components of the Excel Plus Microcentral System												
  		Use the W1044 XPOT to perform Point Data Access and Scheduling functions.  												
  		Perform all operator functions using the provided data entry templates and the 

		short-cuts												
  		Perform/create Microcentral Data View screens/shortcuts using the Keyname Processor													
  		Perform all Microcentral Data Entry functions using the provided templates														
  		Perform the critical Microcentral Database Save/Restore functions using the 

Class Type:	Basic Operation												


System:		Microcentral												


Duration:		4.5 Days													


Class Audience:	Maintenance Personnel responsible for operating the FS90/FS90 						
		Plus Microcentral System with a PC and a Bus Interface																										


Objectives: 	Upon completion of the course the student will be able to:							


  		Identify FS90/FS90 Plus Microcentral System Hardware including the Peer Bus																			
  		Identify software/firmware in all components of the FS90/FS90 Plus Microcentral System																	
  		Perform all field programming functions for the FS90/FS90 Plus downline processors 																	
  		Perform all operator functions using the provided data entry templates and the short-cuts																
 
 		
		Perform/create Microcentral Data View screens/shortcuts using the Keyname Processor																		
  		Perform all Microcentral Data Entry functions using the provided templates																			
  		Use all features of the PC Applications Packages Program except the Optional programs. 																	


Topics:		FS90/FS90 Plus Microcentral System Block Diagram				
		Overview of System Extensions and Enhancements					
		FS90/FS90 Plus System Software/Firmware						
		Operating Procedures								
		Programming/Data Entry Procedures						
		FS90/FS90 Plus Field Programming							
		Keyname Processor								
		PC Applications Packages								
		System Reports									
		Custom Reports									

Class Type:	Data Entry												


System:		Microcentral												

		
Duration:		4.5 Days													


Class Audience:	Maintenance Personnel responsible for operating the Excel Plus 							
		System with a PC and a Bus Interface													


Objectives: 	Upon completion of the course the student will be able to:			


  		Describe the nature and significance of a controller database 								
  		Perform all Database Modification functions using Record Format XPOT															
  		Perform all Database Modification functions using Record Format PPT															
  		Perform all Database Modification functions using Record Format Microcentral															
  		Perform the critical Microcentral Database Save/Restore functions using the 

		PC Application Packages Program.										
		Use all features of the PC Applications Packages Program except the Optional 

		programs. 												


Topics:		Excel Plus Microcentral System Block Diagram												
		Overview of Excel Plus System Software/Firmware														
		Nature and significance of R7044 Databases														
		Controller Database Access/Display/Modify Procedures Using Record Format PPT																			
		Controller Database Access/Display/Modify Procedures Using Record Format Microcentral 																	
		Controller Database Access/Display/Modify Procedures Using Record Format XPOT														
		Overview of Excel Plus Programming												

Class Type:	Programming								


System:		Microcentral								


Duration:		4.5 Days									


Class Audience:	Maintenance Personnel responsible for optimization of a Excel 						
		Plus Microcentral Energy Management System											 																			


Objectives: 	Upon completion of the course the student will be able to:			


  		Define each of the standard Honeywell Energy Management Programs on the Excel Plus 

		Microcentral System								
		Identify the required sensor inputs and actuator outputs of all energy management 

		Programs										
  		Understand the theory of operation and control action of each energy management program .  										
  		Write/Modify each of the energy management programs in order to optimize comfort-energy 

		savings calculus								
  		Test the control action of the major energy management programs					
  		Use Honeywell documentation for planning the Energy-Comfort strategy													
		


Topics:		Excel Plus Microcentral System Block Diagram								
		Energy Management Implementation Provision in CAE, the Database Generation 														
		Program for the Excel Plus Systems												
		Theory of Operation of Each of the Energy Management Programs							
		Program Creation/Modification on-line						
		Program Testing/Optimization							
	         Honeywell Documentation 							
		Strategic use of Standard/Custom Reports						

Class Type:	Programming								


System:		Microcentral								


Duration:		4.5 Days									


Class Audience:	Maintenance Personnel responsible for Customization/Configuration 					
		of an excel Plus Microcentral DDC system																										


Objectives: 	Upon completion of the course the student will be able to:			


  		Identify the Point and Program files of an R7044 Controller database														
  		Understand the nature and significance of an HVAC Control Loop						
  		Flow-chart an HVAC Control Loop using Deltanet Pascal  Standard Programming Symbology												
  		Write program code to implement a flow-chart for an HVAC Control Loop															
  		Compile program code to executable/object code format using the Pascal Compiler														
  		Download object code for a DDC program into an R7044 memory								
  		Test/checkout a downloaded program for correct on-line operation							
  		Use all Honeywell Pascal HVAC operators to write error-free and easily 

		understood programs												

  	
		Eliminate the use of the 'IF' statement from any already written program to 

		enhance program readability 										


Topics:		Excel Plus Microcentral System Block Diagram				
		Controller Point and Program files							
	         DDC control loops								
		Flow-charting									
	         Program Code writing using an editor program					
		Program Compilation								
		Program downloading/Program test/checkout on-line					

Class type:	Programming								


System:		Microcentral								


Duration:		4.5 Days									


Class Audience:	Maintenance Personnel interested in Supervisory/Management 						
		optional programs implemented on the Microcentral Systems																					


Objectives: 	Upon completion of the course the student will be able to:			


  		Identify the purpose and intent of the PC Applications Program										
  		Load the optional programs onto the system hard disk												
  		Verify the correct operation of the loaded programs  												
  		Perform all operating procedures for all 3 of the optional programs																		


Topics:		Excel Plus Microcentral System Block Diagram				
		PC Applications Program								
		Optional Program Loading								
		Optional Program Operation Verification						
	         Operating procedures for the DR HALO Program					
		Operating procedures for the Maintenance Manager Program				
	         Operating Procedures for the Energy Auditor Program				

Class Type:	Programming								


System:		Microcentral								


Duration:		4.5 Days									


Class Audience:	Maintenance/Supervisory Personnel responsible for an Excel Plus 											
		System with a PC and Bus Interface																																					


Objectives: 	Upon completion of the course the student will be able to:						


  		Exhibit independent investigative ability													
  		Exhibit a knowledge of Honeywell Technical Literature Organization									
  		Articulate questions/comments for the Honeywell Rep using technical terminology 																	

	
Topics:		Honeywell Technical Literature Organization									
		Student initiated questions/problems/projects											
		Instructor initiated questions/problems/projects										

Class Type: 	Engineering/Service							


System:		Microcentral 								


Duration:		4.5 Days									


Class Audience:	Mechanical HVAC systems maintenance persons that have 									
		responsibility to maintain or reconfigure Micro/Macrocel systems 										
		integrated with their Excel Plus systems using 												
		Microcentral/Graphic Central front end. Also, Electrical trades 									
		people or Electronic Technicians responsible for 											
		Engineering/Reengineering or Servicing an Excel Plus Microcentral 								
		HVAC System. 																																			


Objectives:	Upon completion of the course the student will be able to:							

	
  		Identify Excel Plus Microcentral System Hardware including the Peer Bus and the C-NAP bus													
  		Identify software/firmware in all components of the Excel Plus Microcentral Central System													
  		Perform all Database Modifications functions using the Interactive 							
		Database Modification Utility of the Honeywell Engineering Program																
  		Perform the Database Validation Function provided in the Honeywell Engineering Program														
  		Interpret and rectify the validation error messages with dispatch																
  		Perform the Database Generation function provided in the Honeywell Engineering Program														
  		Interpret and rectify the Database Generation error messages with dispatch																
  		Perform the Media generation functions provided in the Honeywell Engineering Program 																
  		Generate required reports for analysis														
  		Download Generated Databases to the required downline processors										
  		Test and Checkout on-line the generated Databases after download										


Topics:		Excel Plus Microcentral System Block Diagram								
		Overview of Excel Plus System Software/Firmware										
		Nature and significance of R7044 Databases										
		Controller Database Record Access/Display/Modify Procedures Using the Interactive 

		Database Generator of the Engineering Program														
		Database Validation Procedure												
		Validation Error Messages													
		Database Generation/Compilation											
		Database Generation Error Messages											
		Downloading Processor databases											
		Database Test and Checkout												

Class Type:	Programming								


System:		Graphic Central								


Duration:		2.5 days 								


Class Audience:	Programmers of Excel Plus systems with a Graphic user interface											


Objectives:	Upon completion of the course the student will be able to:							

			
  		Start the Designer program 												
  		Use every design tool provided in the Designer program							
  		Access the Honeywell provided repertoire of graphic objects							
  		Use the copy/paste technique skillfully 										
  		Construct a meaningful graphic hierarchy for any building or make modification to a given one											
  		Assign a graphic to the Graphic User Interface program							
  		Program or reprogram a given graphic using the Graphic User 						
		Interface program													


Topics:		Loading the Designer program										
		Designer Operating Procedures												
		Designing Tools														
		Cut/Copy/Paste technique												
		Graphic Assignment													
		Graphic Programming													
		Graphic Importing														

Class Type:	Programming

System:	 	Graphic Central

Duration:		4.5 days 								


Class Audience:	Programmers of Excel Plus systems with a Graphic user interface		 											


Objectives: 	Upon completion of the course the student will be able to:							

		
  		Identify Excel Plus Graphic Central System Hardware including the Peer Bus															
  		Identify software/firmware in all components of the Excel Plus Graphic Central System													
  		Perform all Database Modifications functions using the Interactive 						
		Database Modification Utility of the Customer Program Pak							
 		Perform the Database Validation Function provided in the Customer Program Pak															
  		Interpret and rectify the validation error messages with dispatch							
  		Perform the Database Generation function provided in the Customer Program Pak															
  		Interpret and rectify the Database Generation error messages with dispatch															
  		Perform the Media generation functions provided in the Customer Program Pak															
  		Generate required reports for analysis												
  		Download Generated Databases to the required downline processors							
  		Test and Check out on-line the Generated Databases after download										


Topics:		Excel Plus Graphic Central System Block Diagram						
		Overview of Excel Plus System Software/Firmware								
		Nature and significance of R7044 Databases								
		Controller Database Record Access/Display/Modify Procedures 					
		Using the Interactive Database Generator of the Customer Program Pak													
		Database Validation Procedure											
		Validation Error Messages											
		Database Generation/Compilation										
		Database Generation Error Messages										
		Processor Loading													
		Database Test and Checkout											

Class Type:	Programming																				

	
System:		Graphic Central																
 

Duration:		4.5 Days																	


Class Audience:	Programmers of an excel Plus System with a Graphic User Interface 																																		


Objectives: 	Upon completion of the course the student will be able to:			


  		Identify the point and program files of an R7044 Controller database																			
  		Understand the nature and significance of an HVAC Control loop											
  		Flow-chart an HVAC Control loop using Deltanet Pascal Standard Programming Symbology																	
  		Use the Editor program provided in the Customer Program Pak to write program code 

		to implement a flow-chart for an HVAC control loop																					
  		Compile program code into the executable/object code format using the Pascal Compiler																	
  		Download object code for a DDC program into an R7044 memory												
  		Test/checkout a downloaded program for correct on-line operation											
  		Use all Honeywell Pascal HVAC operators to write error-free and easily understood programs																
  		Eliminate the use of the 'IF' statement from any already written programs to enhance 

		program functionality and readability for trouble shooting purposes  															


Topics:		Excel Plus Graphic Central System Block Diagram				
		Controller Point and program files							
		DDC control loops								
		Flow-charting									
		Program Code writing using an editor program					
		Program Compilation								
		Program downloading								
		Program test/checkout on-line							

Class Type:	Programming								


System:		Graphic Central								


Duration: 	4.5 Days									


Class Audience:	Mechanical HVAC systems maintenance persons that have 									
		responsibility to maintain or reconfigure Micro/Macrocel systems 									
		integrated with their Excel Plus systems using Graphic Central 									
		front end. Also, Electrical trades people or Electronic 										
		Technicians responsible for Engineering/Reengineering or 										
		Servicing an Excel Plus Graphic Central HVAC System. 																		


Objectives:	Upon completion of the course the student will be able to:							

		
  		Identify Excel Plus Graphic Central System Hardware including the Peer Bus and the C-NAP bus												
  		Identify software/firmware in all components of the Excel Plus Graphic Central System													
  		Perform all Database Modifications functions using the Interactive Database 															
 		Modification Utility of the Engineering Program										
  		Perform the Database Validation Function provided in the Engineering Program													
  		Interpret and rectify the validation error messages with dispatch							
  		Perform the Database Generation function provided in the Engineering Program													
 		Interpret and rectify the Database Generation error messages with dispatch															
  		Perform the Media generation functions provided in the Engineering Program 															
  		Generate required reports for analysis														
  		Download Generated Databases to the required downline processors											
  		Test and Checkout on-line the generated Databases after download												

		
Topics:		Excel Plus Graphic Central System Block Diagram											
		Overview of Excel Plus System Software/Firmware													
		Nature and significance of R7044 Databases													
	 	Controller Database Record Access/Display/Modify Procedures using the 

		Interactive Database Generator function of the Engineering Program																
		Database Validation Procedure																
		Validation Error Messages																
		Database Generation/Compilation															
		Database Generation Error Messages															
		Downloading Processor Databases															
		Database Test and Checkout											


																

Class Type:	Engineering/Service							


System:		Micro/Graphic Central							


Duration:		2.5 Days									


Class Audience:	Maintenance Personnel responsible for maintaining the downline 									
		FS90/FS90 Plus Fire Alarm Processors															


Objectives: 	Upon completion of the course the student will be able to:			


  		Identify all components of Honeywell Higher Order User Interfaces							
  		Identify all components of an FS90/FS90 Plus panel									
  		Operate any downline Fire Alarm Processor  										
  		Read and Understand the configuration of an FS90/FS90 Plus Panel							
  		Build a Fire Alarm Panel with given Honeywell Fire Alarm 								
		Parameters as a learning/diagnostic and trouble hooting technique  													
  	  	Program the downline Fire Alarm processors in the field and understand 

	 	the limitations of this process Understand the FS90/FS90 Plus interface 

Class Type:	Programming								


System:		Graphic Central								


Duration:		4.5 Days									


Class Audience:	Mechanical Fire Alarm systems maintenance persons that have 											
		responsibility to maintain or reconfigure Microcentral/Graphic 										
		Central systems integrated with FS90/FS90 Plus or Delta 1000 Fire 									
		Alarm Systems using FS90/FS90Plus Panels. Also, Electrical trades 									
		people or Electronic Technicians responsible for Engineering/										
		Reengineering or Servicing an FS90/FS90 Plus Alarm System with a 										
		Graphic Central/Microcentral or Delta 1000 front-end. 																									


Objectives:	Upon completion of the course the student will be able to:			

		
  		Identify Excel Plus Graphic Central/Microcentral System Hardware 										
		including the F&S Bus, Fire Alarm Equipment and Fire Alarm Processors																	
  		Identify software/firmware in all components of the Graphic Central/Microcentral Central Fire Alarm Systems												
  		Perform all Database Modification functions using the Interactive Database Modification Utility of the 											
		Engineering Program																
 		Perform the Database Validation Function provided in the Engineering Program																
  		Interpret and rectify the validation error messages with dispatch																		
  		Perform the Database Generation function provided in the Engineering Program																
  		Interpret and rectify the Database Generation error messages with dispatch																
  		Perform the Media generation functions provided in the Engineering Program 																
  		Generate required reports for analysis														
 		Install Generated Databases into the required downline Fire Alarm Processors																	
 		Test and Checkout on-line the installed databases												


Topics:		Microcentral/Graphic Central System Block Diagram													
		Overview of Fire Alarm System Software/Firmware																
		Processor Database Record Access/Display/Modify Procedures														
		Database Validation Procedure																			
		Validation Error Messages																			
		Database Generation/Compilation																		
		Database Generation Error Messages																		
		Installing Processor Databases																		
		Database Test and Checkout																			

Class Type:	Basic Operation								


System:		Graphic Central/XBS-i								


Duration:		2.5 Days									


Class Audience:	Maintenance Personnel Responsible for Operating the 									
		Deltanet Access Control Program Module Implemented in the Micro 									
		Central/Graphic Central Application Program for the Downline									
		Access Management Controllers and Card Readers 											


Objectives:	Upon completion of the course the student will be able to:							

		
  		Identify all components of a Graphic Central/XBS-i Higher Order User Interface																	
  		Identify all components of an Access Management Controller Panel												
  		Start/sign on/sign off the Graphic/XBS-i User interface and the DAC Program Module																
 		Perform all Area Management Functions														
  		Perform all Elevator Management Functions																		
  		Perform all Card Related Functions																
  		Perform all Database Management Functions 																										


Topics:		Honeywell User Interface Block Diagrams													
		Access Management Controller Hardware Layout												
		Basics of Graphic Central/XBS-i Operating Procedures											
		Deltanet Access Control Operating Procedures												
		Database Management Procedures														

Class Type:	Basic Operation								


System:		Graphic Central/XBS-i								


Duration:		2.5 Days									


Class Audience:	Maintenance Personnel Responsible for maintaining 										
		the downline Access Management															


Objectives:	Upon completion of the course the student will be able to:							

		
  		Identify all components of a Graphic Central/XBS-i Higher Order 											
		User Interface																	
  		Identify all components of an Access Management Controller Panel												
  		Start/sign on/sign off the Graphic/XBS-i User interface and the 														
		DAC Program Module																
 		Perform all Area Management Functions														
  		Perform all Elevator Management Functions																		
  		Perform all Card Related Functions																
  		Perform all Database Management Functions 																										


Topics:		Honeywell User Interface Block Diagrams													
		System Layout of an Access Management Controller									
		Access Management Controller Configuration/Wiring												
		Access Management Controller Operating Procedures											
		Access Management Controller Field Programming 												
		Building an Access Management Controller with given Access 											
		Control Parameters																	
		Test and Checkout																																					

Class Type:	Engineering/Service								


System:		Graphic Central/XBS-i								


Duration:		4.5 Days									


Class Audience:	Access Management Systems maintenance persons that have 												
		responsibility to maintain or reconfigure Graphic Central/XBS-i 													
		systems integrated with Access Management Controllers. Also, 													
		electrical trades people or Electronic Technicians responsible for 												
		Engineering/Reengineering or Servicing an Access Management 													
		Controller System with a Graphic Central/XBS-i front-end.																																						


Objectives:	Upon completion of the course the student will be able to:							

			
  		Identify Excel Plus Graphic Central/Microcentral System Hardware including the 

		F&S Bus, Fire Alarm Equipment and Fire Alarm Processors																		
  		Identify software/firmware in all components of the Graphic Central/XBS-i Access 

		Management Systems																
 		Perform all Database Modification/Creation functions using the Interface Database 

		Modification Utility of the Engineering Program																	
  		Perform the Databse Validation Function provided in the Engineering Program																				
  		Interpret and rectify the validation error messages with dispatch																
  		Perform the Database Generation function provided in the Engineering Program																		
		Interpret and rectify the Database Generation error messages with dispatch 																										
		Perform the Media generation functions provided in the Engineering Program																		
		Generate required reports for analysis													
		Install Generated Databases into the required downline Access Management Controllers														
		Test and Checkout on-line the installed databases.										


Topics:		Microcentral/Graphic Central System Block Diagram																	
		Overview of Access Management Controller System Software/Firmware																	
		Database Validation Procedure																
		Validation Error Messages																
		Database Generation/Compilation 															
		Database Generation Error Messages														
		Installing Processor Databases																	
		Database Test and Checkout																

Class Type:	Engineering/Service								


System:		XL5000								


Duration:		4.5 Days									


Class Audience:	Fire and Security Systems Service/Installation Personnel																																					


Objectives:	Upon completion of the course the student will be able to:							

		
  		Describe all Cabinets and Chassis modules																	
  		Verify integrity of all field wiring																				
  		Describe all chassis components and verify inter-chassis cables																
 		Perform all LRM wiring																							
  		Apply AC power and connect all batteries involved																		
  		Download the initial start-up version of the CITS-generated application program																							
  		Connect all field devices including signatures series devices and remove all wiring problems																	
		Download the CITS-generated final application program and configure the XBS front-end																	
		Verify proper system operation through system test and checkout																										



Topics:		System Block Diagram																	
		Enclosures																					
		System Wiring																				
		Chassis Components																			
		Local Rail Modules 																			
		Remote Devices including Signature Series Devices																						
		Application Program Downloading																		
		System Test and Checkout																			

Class Type:	Engineering								


System:		PC Hardware/Software											


Duration:		4.5 Days												


Class Audience:	Maintenance Personnel responsible for maintaining the PC Equipment for any Honeywell 

		PC Based HVAC System.											

Objectives:	Upon completion of the course the student will be able to:						
		
  		Identify all components of an IBM compatible PC																	
  		Use a basic but critical set of DOS commands																				
  		Run and Interpret and standard Diagnostics program on a PC																
 		Run and Interpret the Debug program on the PC																							
  		Perform all repair functions for the PC																		
  		Load and run any DOS based Honeywell program																														


Topics:		PC Architecture																	
		DOS commands and Windows Operation																					
		PC Diagnostics Program																				
		PC Debug																			
		I/O Port Addresses and IRQ's																			
		PC Upgrading																						
		PC Repair														
		Honeywell Software Loading											

Class Type:	Engineering								


System:		PC Hardware/Software											


Duration:		4.5 Days												


Class Audience:	Maintenance Personnel responsible for maintaining the PC Equipment for any Honeywell 

		PC Based HVAC System.											


Objectives:	Upon completion of the course the student will be able to:							

		
  		Identify all components of an IBM compatible PC																	
  		Use a basic but critical set of DOS commands																				
  		Run and Interpret and standard Diagnostics program on a PC																
 		Run and Interpret the Debug program on the PC																							
  		Perform all repair functions for the PC																		
  		Load and run any DOS based Honeywell program																														


Topics:		PC Architecture																	
		DOS commands and Windows Operation																					
		PC Diagnostics Program																				
		PC Debug																			
		I/O Port Addresses and IRQ's																			
		PC Upgrading																						
		PC Repair														
		Honeywell Software Loading														




















										

Class Type:	Engineering								


System:		PC Hardware/Software											


Duration:		4.5 Days												


Class Audience:	Maintenance Personnel responsible for maintaining the PC Equipment for any Honeywell 

		PC Based HVAC System.											


Objectives:	Upon completion of the course the student will be able to:							

		
  		Identify all components of an IBM compatible PC																	
  		Use a basic but critical set of DOS commands																				
  		Run and Interpret and standard Diagnostics program on a PC																
 		Run and Interpret the Debug program on the PC																							
  		Perform all repair functions for the PC																		
  		Load and run any DOS based Honeywell program																														



Topics:		PC Architecture																	
		DOS commands and Windows Operation																					
		PC Diagnostics Program																				
		PC Debug																			
		I/O Port Addresses and IRQ's																			
		PC Upgrading																						
		PC Repair														
		Honeywell Software Loading																

Class Type:	Engineering								


System:		PC Hardware/Software											


Duration:		4.5 Days												


Class Audience:	Maintenance Personnel responsible for maintaining the PC Equipment for any Honeywell 

		PC Based HVAC System.											


Objectives:	Upon completion of the course the student will be able to:							

		
  		Identify all components of an IBM compatible PC																	
  		Use a basic but critical set of DOS commands																				
  		Run and Interpret and standard Diagnostics program on a PC																
 		Run and Interpret the Debug program on the PC																							
  		Perform all repair functions for the PC																		
  		Load and run any DOS based Honeywell program																														



Topics:		PC Architecture																	
		DOS commands and Windows Operation																					
		PC Diagnostics Program																				
		PC Debug																			
		I/O Port Addresses and IRQ's																			
		PC Upgrading																						
		PC Repair														
		Honeywell Software Loading																

Class Type:	Engineering								


System:		PC Hardware/Software											


Duration:		4.5 Days												


Class Audience:	Maintenance Personnel responsible for maintaining the PC Equipment for any Honeywell 

		PC Based HVAC System.											


Objectives:	Upon completion of the course the student will be able to:							

		
  		Identify all components of an IBM compatible PC																	
  		Use a basic but critical set of DOS commands																				
  		Run and Interpret and standard Diagnostics program on a PC																
 		Run and Interpret the Debug program on the PC																							
  		Perform all repair functions for the PC																		
  		Load and run any DOS based Honeywell program																														


Topics:		PC Architecture																	
		DOS commands and Windows Operation																					
		PC Diagnostics Program																				
		PC Debug																			
		I/O Port Addresses and IRQ's																			
		PC Upgrading																						
		PC Repair														
		Honeywell Software Loading																

Class Type:	Engineering								


System:		PC Hardware/Software											


Duration:		4.5 Days												


Class Audience:	Maintenance Personnel responsible for maintaining the PC Equipment for any Honeywell 

		PC Based HVAC System.											


Objectives:	Upon completion of the course the student will be able to:							

		
  		Identify all components of an IBM compatible PC																	
  		Use a basic but critical set of DOS commands																				
  		Run and Interpret and standard Diagnostics program on a PC																
 		Run and Interpret the Debug program on the PC																							
  		Perform all repair functions for the PC																		
  		Load and run any DOS based Honeywell program																														


Topics:		PC Architecture																	
		DOS commands and Windows Operation																					
		PC Diagnostics Program																				
		PC Debug																			
		I/O Port Addresses and IRQ's																			
		PC Upgrading																						
		PC Repair														
		Honeywell Software Loading												

Class Type:	Engineering								


System:		PC Hardware/Software											


Duration:		4.5 Days												


Class Audience:	Maintenance Personnel responsible for maintaining the PC Equipment for any Honeywell 

		PC Based HVAC System.											


Objectives:	Upon completion of the course the student will be able to:							

		
  		Identify all components of an IBM compatible PC																	
  		Use a basic but critical set of DOS commands																				
  		Run and Interpret and standard Diagnostics program on a PC																
 		Run and Interpret the Debug program on the PC																							
  		Perform all repair functions for the PC																		
  		Load and run any DOS based Honeywell program																														


Topics:		PC Architecture																	
		DOS commands and Windows Operation																					
		PC Diagnostics Program																				
		PC Debug																			
		I/O Port Addresses and IRQ's																			
		PC Upgrading																						
		PC Repair														
		Honeywell Software Loading	

Class Type:	Engineering								


System:		PC Hardware/Software											


Duration:		4.5 Days												


Class Audience:	Maintenance Personnel responsible for maintaining the PC Equipment for any Honeywell 

		PC Based HVAC System.											


Objectives:	Upon completion of the course the student will be able to:							

		
  		Identify all components of an IBM compatible PC																	
  		Use a basic but critical set of DOS commands																				
  		Run and Interpret and standard Diagnostics program on a PC																
 		Run and Interpret the Debug program on the PC																							
  		Perform all repair functions for the PC																		
  		Load and run any DOS based Honeywell program																														


Topics:		PC Architecture																	
		DOS commands and Windows Operation																					
		PC Diagnostics Program																				
		PC Debug																			
		I/O Port Addresses and IRQ's																			
		PC Upgrading																						
		PC Repair														
		Honeywell Software Loading														

Class Type:	Engineering								


System:		PC Hardware/Software											


Duration:		4.5 Days												


Class Audience:	Maintenance Personnel responsible for maintaining the PC Equipment for any Honeywell 

		PC Based HVAC System.											


Objectives:	Upon completion of the course the student will be able to:							

		
  		Identify all components of an IBM compatible PC																	
  		Use a basic but critical set of DOS commands																				
  		Run and Interpret and standard Diagnostics program on a PC																
 		Run and Interpret the Debug program on the PC																							
  		Perform all repair functions for the PC																		
  		Load and run any DOS based Honeywell program																														


Topics:		PC Architecture																	
		DOS commands and Windows Operation																					
		PC Diagnostics Program																				
		PC Debug																			
		I/O Port Addresses and IRQ's																			
		PC Upgrading																						
		PC Repair														
		Honeywell Software Loading														

Class Type:	Engineering								


System:		PC Hardware/Software											


Duration:		4.5 Days												


Class Audience:	Maintenance Personnel responsible for maintaining the PC Equipment for any Honeywell 

		PC Based HVAC System.											


Objectives:	Upon completion of the course the student will be able to:							

		
  		Identify all components of an IBM compatible PC																	
  		Use a basic but critical set of DOS commands																				
  		Run and Interpret and standard Diagnostics program on a PC																
 		Run and Interpret the Debug program on the PC																							
  		Perform all repair functions for the PC																		
  		Load and run any DOS based Honeywell program																														



Topics:		PC Architecture																	
		DOS commands and Windows Operation																					
		PC Diagnostics Program																				
		PC Debug																			
		I/O Port Addresses and IRQ's																			
		PC Upgrading																						
		PC Repair														
		Honeywell Software Loading														

Class Type:	Engineering								


System:		PC Hardware/Software											


Duration:		4.5 Days												


Class Audience:	Maintenance Personnel responsible for maintaining the PC Equipment for any Honeywell 

		PC Based HVAC System.											


Objectives:	Upon completion of the course the student will be able to:							

		
  		Identify all components of an IBM compatible PC																	
  		Use a basic but critical set of DOS commands																				
  		Run and Interpret and standard Diagnostics program on a PC																
 		Run and Interpret the Debug program on the PC																							
  		Perform all repair functions for the PC																		
  		Load and run any DOS based Honeywell program																														


Topics:		PC Architecture																	
		DOS commands and Windows Operation																					
		PC Diagnostics Program																				
		PC Debug																			
		I/O Port Addresses and IRQ's																			
		PC Upgrading																						
		PC Repair														
		Honeywell Software Loading																																

Class Type:	Basic Operation								


System:		XBS Central								


Duration:		3.0 days 								


Class Audience:	Operators of down-line XBS processors and/or maintenance personnel or the XBS 

		Controllers in XBS Central or XBS-i Central HVAC Systems																						


Objectives:	Upon completion of the course the student will be able to:			


  		Describe the hardware components of the XBS Central System													
  		Connect an operator unit to any Excel Controller														
  		Work with the operator unit keyboard, the screens and the menus												
  		Perform all daily functions on the operator units such as sign-on/sign-off, viewing 

		alarm information, requesting trend logs and system point data access															
  		Perform all data access functions 																	
  		Modify all time program elements																	
  		Perform all controller Save/Restore functions															


Topics:		System Block Diagram																
		System Operator Units																		
		Operator Unit Operating Procedures																
		Save/Restore Functions																		

Class Type:	Maintenance								


System:		XBS Central								


Duration:		4.5 days 								

											
Class Audience:	Operators of down-line XBS processors and/or Maintenance personnel 
		for the XBS Controllers in XBS or XBS-i Central HVAC Systems					

                              
Objectives:	Upon completion of the course the student will be able to:			


  		Describe the hardware components of the XBS Central System													
  		Exhibit an understanding of the function and purpose of each Hardware Module in the 

		XBS System																			
  		Demonstrate a working knowledge/logical understanding of the XBS Engineering Process																				
  		Exhibit a maintenance knowledge of all technical modules of all Excel controllers																	
  		Run the provided Test and Checkout programs to exercise the Excel Controllers 																	
  		Exhibit knowledge of all wiring termination's from the maintenance point of view																	
  		Perform all controller Save/Restore functions																	
  		Interpret and use site documentation created by Honeywell or other engineers																		
  		Use Test and Checkout tools developed by CITS  																		





Topics:		System Hardware/Software Overview														
		Technical Descriptions of all Excel Controller Modules and their Functions																	
		Point Data Access for Maintenance work																				
		Controller Commissioning																					
		Bus Communication Problems																				
		Excel Controller Problems																				

Class Type: 	Installation								


System:		XBS Central								


Duration:		3.0 days 								


Class Audience:	Operators of down-line XBS processors and/or maintenance personnel for the XBS 

		Controllers in XBS Central or XBS-i Central HVAC Systems																																			


Objectives:	Upon completion of the course the student will be able to:																


  		Describe the hardware components of the XBS Central System														
  		Exhibit an understanding of the function and purpose of each Hardware Module in 

		the XBS system																	
  		Demonstrate a working knowledge/logical understanding of the XBS Engineering Process																			
  		Unpack and physically mount all Excel Hardware	 															
  		Perform all wiring termination's for all Excel Hardware Modules													
  		Exhibit knowledge of all wiring termination's from the maintenance point of view																				
  		Perform all controller Load/Dump and software/firmware install functions																				
  		Interpret and use site documentation created by Honeywell or other engineers																				


Topics:		System Hardware/Software Overview																	
		Unpacking/mounting of all Excel Controller Modules and other components																						
		System Wiring Termination's																				
		System Documentation Interpretation																			

Class Type: 	Engineering/Service												


System:		XBS Central												


Duration:		4.5 days 													

	
Class Audience:	Operators of down-line XBS processors and/or maintenance personnel for the XBS 

Class Type:	Basic Operation								


System:		XBS Central								


Duration:		4.5 days 								


Class Audience:	Operators of  XBS systems and/or Maintenance personnel for the XBS Controllers in 

		XBS Central or XBS-i Central HVAC Systems																									


Objectives:	Upon completion of the course the student will be able to:												


  		Identify functionally critical components of the XBS Central System.																					
  		Understand the purpose and function of functionally critical components of the XBS 

		Central System. 																
  		Perform all daily and routine functions on the XBS Central System. 												
  		Perform all System Data Modification functions provided in the XBS Central System.																				
  		Perform all standard report generation functions.															
  		Appreciate the need for well-documenting the XBS Central System													

                                      																		
Topics:		XBS Central System Block Diagram														
		Basics of the Windows Operating System															
    		XBS Central Screen Conventions																
		System Data Access																		
		Operating Procedures 	   																	
		Data Modification Procedures																	
		Report Generation	    																		

Class Type:	Programming																	


System:		XBS Central																	


Duration:		3.0 days 																		


Class Audience:	Programmers of down-line XBS processors and/or Maintenance personnel for the XBS 

Class Type:	Programming								


System:		XBS Central								


Duration:		3.0 days 								


Class Audience:	Programmers of down-line XBS processors and/or Maintenance personnel for the XBS 

		Controllers in XBS Central or XBS-i Central HVAC Systems																																							





Objectives:	Upon completion of the class the student will be able to:												


  		Display/Print all System Graphics																				
  		Delete a graphic from the XBS system																			
  		Display and Change the Graphic Point Information																	
  		Display the Color Dialog Box and be able to use all features provided in it																						
  		Create/Change/Modify a Graphic Penetration Structure/Scheme																
  		Program graphics using the Graphic Programming Dialog Box																
  		Program graphic, command, animation, text, and point ID symbols 															


Topics:		Typical Graphic Procedures																			
		Creating/modifying/changing Graphic hierarchical structures																
		Assigning Graphic ID's/Creating clickable areas																		
		Programming Graphic ID's																					
		Testing Graphic schemes for proper operation																		

	

Class Type: 	Programming								


System:		XBS Central								


Duration:		3.0 days 								


Class Audience:	Programmers of down-line XBS processors and/or Maintenance personnel for the XBS 

		Controllers in XBS Central or XBS-i Central HVAC Systems																		

                              
Objectives:	Upon completion of the course the student will be able to:												


  		Describe what a SmartPad is																
  		Identify the various Pad Styles															
  		Configure a Pad Button Using all Button Functions 												
  		Operate the SmartPad in Configuration and Server Modes											
  		Start the SmartPad Software																
  		Create a SmartPad 																	
  		Use all Configuration Commands for a Pad or Button												
  		Perform Pad Association Functions															
  		Perform Pad Resizing/Styling/Button Detail Functions												
  		Perform all Macro/Viewer Functions for a Pad													
  		Establish DDE Conversation with another Windows Application											
  		Use effectively the QuickLearn Feature of the SmartPad Functionality																
  		Perform all DDE Execute Commands														
  		Perform all Replacement String Function Programming											


Topics:		SmartPad Basics												
		SmartPad Operation and Usage												
		Button and Pad Creation/Configuration										
		Pad Association/Resizing/Styling/Button Details									
		DDE Execute															
		Macro/Viewer Functions/Programming											
		QuickLearn Feature													
		Replacement String Function Programming										
		SmartPad Initialization Parameters											
		SmartPad Error Messages													

Class Type: 	Programming								


System:		XBS Central								


Duration:		4.5 days 								


Class Audience:	Programmers of down-line XBS processors and/or Maintenance personnel for the XBS 

		Controllers in XBS Central or XBS-i Central HVAC Systems																						

                             
Objectives:	Upon completion of the course the student will be able to:							

		
  		Physically wire up/connect up an XI584 Computer System 						
  		Start-Up an XI584 system													
  		Perform Sign-on and sign-off and other basic Startup functions							
  		Perform all Typical Procedures such as, Check System Status, 							
		Controller Data File Changes, Clear Controller Datafiles, 							
		Find and Display Point Information, Respond to Alarms, 							
		Create/Modify Schedules, and Report Generation Functions 															
		Perform all CARE Project Administration Functions									
  		Modify/Change all DDC Parameters												
  		Modify/Change Controller Databases												
  		Perform Backup/Restore Functions												
  		Perform Applicable Subsystem Access Functions										
  		Emulate XI581 Terminal														
  		Perform all Applicable Text Database (such as Descriptor files) 							
		Modification Functions  												


Topics:		XI584 Wiring and Start-Up											
		Sign-on/sign-off															
		Controller Database Changes													
		Clear Controller Database Procedures											
		Find and Display Point Information												
		Respond to Alarm functions													
		Change/Modify Schedules														
		System Reports															
		CARE Project Administration Functions											
		Change/Modify DDC Parameters													
		Database Save/Restore Functions												
		XI581 Emulation															

Class Type: 	Installation								


System:		XBS Central								


Duration:		4.5 days 								


Class Audience:	Electricians, electronic systems specialists, maintenance persons 									
		responsible for electrical/electronic installation work at 													
		customer sites, Honeywell Authorized System Distributor 													
		Installation personnel, and Honeywell systems technicians for 												
		XBS or other systems and Programmers/analysts familiar with PC 												
		Hardware and Application programs, and Windows. 														










                               
Objectives:	Upon completion of the course the Student will be able to:												


  		Understand a given site documentation prepared by Honeywell or other engineers																			
  		Verify remote hardware/software/firmware installation for proper operation																				
  		Set-up and connect bus interfaces and PC workstations															
  		Install bus interface and PC workstation software															
  		Verify system operating sequences																		
  		Perform all test and checkout procedures																	
  		Generate final list of input/output Points for the entire system as built)																						

	
Topics:		Analysis of system documentation as prepared by Honeywell or other engineers																
		Review of installed remote system hardware/software 											
		Review of remote system hardware operation												
		Central System PC workstation wiring and set-up												
		Central system software loading 														
		Central system test and checkout for all types of XBS configurations including LAN's 													
		XBS Modem Systems Set-up 															
		XBS System Bus Configurations															

Class Type: 	Programming								


System:		XBS Central								


Duration:		4.5 days 								


Class Audience:	Programmers of down-line XBS processors and/or Maintenance 										
		personnel for the XBS Controllers in XBS or XBS-i Central HVAC 											
		Systems																							


Objectives:	Upon completion of the course the student will be able to:							


  		Start the Honeywell CARE Application Program									
  		Sign-on/sign-off from CARE System											
  		Open an existing CARE project												
  		Open an existing Plant 													
  		Select a controller													
  		Define a new Controller													
  		Attach/detach a Plant													
  		Delete a controller													
  		Modify/Change Physical Point types											
  		Modify/Change User Addresses												
  		Modify/Change Basic Control Strategy and Basic Switching Logic 						
  		Modify/Change Time Programs												


Topics:		CARE Start-Up												
		Basic Navigation through the CARE Screens										
		Point Database Modification Procedures										
		Elements of Control Strategy and Switching Logic								
		Time Programs														

	

Class Type: 	Programming								


System:		XBS Central								


Duration:		4.5 days 								


Class Audience:	Programmers of  down-line XBS processors and/or Maintenance 								
		personnel for the XBS Controllers in XBS or XBS-i Central 											
		HVAC Systems																		


Objectives:	Upon completion of the course the student will be able to:			


  		Start the Honeywell CARE Application Program														
  		Sign-on/sign-off from CARE System																
  		Open an existing CARE project																	
  		Open an existing Plant 																		
  		Select a controller																		
  		Attach/detach a Plant																		
  		Delete a controller																		
  		Interpret a given Control Strategy																
  		Modify/Change extensively any given Control Strategy and Switching Logic 																				
  		Create new Control Strategies and Switching logics														

	
Topics:		CARE Start-Up																	
		Basic Navigation through the CARE Screens															
		Interpretation of control Strategies and Switching Logics												
		Elements of Control Strategy and switching Logic													
		Time Programs																			

Class Type: 	Programming								


System:		XBS Central								


Duration:		4.5 days 								


Class Audience:	Programmers of  down-line XBS processors and/or Maintenance 								
		personnel for the XBS Controllers in XBS or XBS-i Central 										
		HVAC Systems																		

	
Objectives:	Upon completion of the course the student will be able to:											


  		Start the Honeywell CARE Application Program													
  		Sign-on/sign-off from CARE System															
  		Open an existing CARE project																
  		Open an existing Plant 																	
  		Attach/detach a Plant																	
  		Interpret a given Control Strategy and Switching Logic											
  		Create New Control Strategies using Excel Control Icons extensively																		
  		Modify/Change any Control Strategy and any Switching Logic using Excel Control Icons 																		
  		Exhibit power-usage of Excel Graphic Application Programming using Excel Control Icons															
  		Convert any Control Strategy and  Switching Logic to incorporate Excel Control Icons																					


Topics:		CARE Start-Up															
		Basic Navigation through the CARE Screens													
		Elements of Control Strategy and Switching Logic											
		Analysis of Excel Control Icons														
		Usage of Excel Control Icons in Graphic Program Segments										
		Test and checkout of Graphic Programs using Excel Control Icons									

Class Type: 	Engineering								


System:		XBS Central								


Duration:		5.0 days, 10 Hours/Day							


Class Audience:	Electricians, electronic systems specialists, maintenance persons 					
		responsible for electrical/electronic installation work at 									
		customer sites, Honeywell Authorized System Distributor 									
		Installation personnel, and Honeywell systems technicians for 								
		XBS or other systems and Programmers/analysts familiar with PC 								
		Hardware and Application programs, and Windows. 										

                                                     
Objectives:	Upon completion of the course the student will be able to:			


  		Start the Honeywell CARE Application Program																
  		Sign-on/sign-off from CARE System																
  		Perform all opening and closing functions for all CARE Database Elements such as 

		controllers and plants										
  		Perform all creation functions for all CARE Database Elements such as Excel Project 

		Creation											
  		Perform all Management functions for Projects, Plants and Controllers															
  		Attach/detach a Plant														
  		Perform all Plant Schematics functions to prepare for a fully functional application 

		for any applicable controller								
  		Program all necessary control Strategies to deliver a fully functional application 

		for the end-user										
  		Program all necessary Switching Logic functions to deliver a fully functional application 

		for the end-user									
  		Program all time program functions necessary to deliver a fully functional application 

		for the end-user										
  		Work with all System Editors for text programming functions such as point descriptors 

		and many others elements									
  		Translate all plants successfully to generate a fully functional application for the end-user												
		Generate all system documentation for the end-user									
  		Perform professionally all file management functions for the created site database such 

		as backup/restore, upload/download controllers, EPROM programming, import/export functions 

		to Element Library									

	
Topics:		Loading  CARE and preparing PC to run CARE								
		Use of Serialized Protection disks and Blocks										
		CARE Start-Up															
		Basic Navigation through the CARE Screens											
		All Point Database Modification/Management Procedures									
		All Control Strategy/switching Logic Procedures										
		All System Editors														
		Time programs															
		Plant Translation															
		System Documentation														
		File Management															

			

Class Type: 	Engineering/Maintenance							


System:		XBS Central								


Duration:		3 days									


Class Audience:	Electricians, electronic systems specialists, maintenance 									
		persons responsible for electrical/electronic installation work 										
		at customer sites, Honeywell Authorized System Distributor 											
		Installation personnel, and Honeywell systems technicians for 										
		XBS or other systems and Programmers/analysts familiar with PC 										
		Hardware and Application programs, and Windows.													
		Additionally the class is highly recommended by CITS for 											
		maintenance/service personnel such as Operators/Programmers of  										
		XBS systems and/or Maintenance personnel for the XBS 												
		Controllers in XBS Central or XBS-i Central HVAC Systems.											

                                                    												
Objectives:	Upon completion of the course the student will be able to:			

		
  		Initiate Controller Simulation																
  		Connect to controller																		
  		Initiate/Exit Live Care																		
  		Use on-line Help																			
  		Select a Plant																			
  		Monitor/fix Points																		
  		Change Control Symbol Parameters																
  		View Control Strategy																		
  		View Switching Logic																		
  		View user Addresses																		
  		View/Modify Excel 10 Information including Diagnostic Information															

			
Topics:		Live CARE Concepts															
		Live CARE Start-Up																	
		Controller Simulation																	
		Live CARE Initiation																	
		Typical Procedures/Working with Controller Information											
		Control Strategies																	
		Switching Logics																		
		User Addresses																		
		Working with Excel 10 Information															

	







	

Class Type: 	Engineering								

	
System:		XBS Central								


Duration:		4.5 days 								


Class Audience:	Electricians, electronic systems specialists, maintenance 									
		persons responsible for electrical/electronic installation work at 									
		customer sites, Honeywell Authorized System Distributor 											
		Installation personnel, and Honeywell systems technicians for XBS 									
		or other systems and Programmers/analysts familiar with PC 											
		Hardware and Application programs, and Windows. 																												


Objectives:	Upon completion of the course the student will be able to:											


  		Start the Honeywell CARE Application Program													
  		Sign-on/sign-off from CARE System															
  		Perform all Plant Schematic functions Using the Control Icon Libraries to prepare 

		a fully functional application for any applicable controller															
  		Program all necessary control Strategies Using the Control Icon Libraries to deliver 

		a fully functional application for the end-user																	
  		Program all necessary Switching Logic functions Using the Control Icon Libraries to 

		deliver a fully functional application for the end-user																	
  		Test and checkout all created applications using the Control Icon Libraries for proper 

		operation																	

			
Topics:		Basic Navigation through the CARE Screens														
		Analysis/discussion/study all Control Icon Library Symbols													
		Test/checkout of all Control Icon Library Symbols														


	

Class Type: 	Engineering								


System:		XBS Central								


Duration:		5.0 days 								


Class Audience:	Electricians, electronic systems specialists, maintenance persons 									
		responsible for electrical/electronic installation work at 													
		customer sites, Honeywell Authorized System Distributor 													
		Installation personnel, and Honeywell systems technicians for 													
		XBS or other systems and Programmers/analysts familiar with 													
		PC Hardware and Application programs, and Windows. 																	

                               
Objectives:	Upon completion of the course the student will be able to:			


  		Install ZM7604/ZM5001 software																
  		CARE Configuration for ZM7604/ZM5001 Software														
  		Perform all Set-up and configuration Functions for the ZM7604/ZM5001 Software														
  		Configure W7620 Controllers														
  		Configure W7600 Networkable Controllers												
  		Configure Building DDC Controllers													
  		Configure Excel Link SSI's														
  		Perform all Database Programming functions for all applicable controllers															
  		Print all reports for the all applicable controller Databases							


Topics:		Starting ZM7604/ZM5001 Software														
		Configuring System Information																
		Configuring Communication Information															
		Configuration flow for a site																	
		Configuring a site																		
		Opening/closing a site																		
		Reading/writing all applicable Controllers														
		Site Connect																			
		Backup/restore for a site or system																

	

Class Type: 	Engineering								


System:		XBS Central								


Duration:		4.5 days 								


Class Audience:	Electricians, electronic systems specialists, maintenance persons 									
		responsible for electrical/electronic installation work at 										
		customer sites, Honeywell Authorized System Distributor 										
		Installation personnel, and Honeywell systems technicians for 									
		XBS or other systems and Programmers/analysts familiar with 									
		PC Hardware and Application programs, and Windows. 																		


Objectives:	Upon completion of the course the student will be able to:											

		
  		Identify XBS Central System Hardware including the Peer Bus and the C-NAP bus																		
  		Identify software/firmware in all components of the XBS Central System																				
  		Perform all Database Modifications functions using the Interactive Database 																				
		Modification Utility of the MPPT Program																
  		Perform all system programming functions using the MPPT Program												
  		Interpret and rectify all error messages with dispatch													
 		Perform the Database Compilation function using the MPPT Program												
 		Generate required reports for analysis																
  		Download Generated Databases to the required downline processors												
  		Test and Checkout on-line the generated Databases after download												

	
Topics:		XBS Central System Block Diagram													
		Overview of Excel Plus System Software/Firmware													
		Nature and significance of MCEL Databases														
		Controller Database Record Access/Display/Modify Procedures											
		Database Generation/Compilation															
		Database Generation Error Messages															
		Downloading Processor databases															
		Database Test and Checkout																















	

Class Type: 	Engineering								


System:		XBS Central								


Duration:		4.5 days 								


Class Audience:	Electricians, electronic systems specialists, maintenance persons 									
		responsible for electrical/electronic installation work at 													
		customer sites, Honeywell Authorized System Distributor 													
		Installation personnel, and Honeywell systems technicians for XBS 												
		or other systems and Programmers/analysts familiar with PC 														
		Hardware and Application programs, and Windows. 																																


Objectives:	Upon completion of the course the student will be able to:			


  		Determine the end-user application programming requirements											
  		Create/Program an application in its entirety and independently using the graphic 

		programming tools, Excel Control Icon libraries and the Standardized Application 

		Library 											
  		Modify/rewrite an application of any complexity using all programming tools 																
  		Test the created applications in their entirety													


Topics:		Review of all graphic programming tools									
		Analysis/test/checkout of Standardized Application Library Programs																
		Creation of complete applications Using Application Library Programs																	
		Creating/modifying new Standardized Applications									
		Testing applications														

Class Type:	Engineering								


System:		XL5000								


Duration:		4.5 days 								


Class Audience:	Technicians installing/servicing down-line satellite Excel 10 									
		W7750A/B Controllers connected to an XBS system and/or maintenance										
		personnel responsible for the same.																

                              
Objectives:	Upon completion of the course the student will be able to:											


  		Identify functionally critical components of a connected E-Bus												
		Understand the purpose and function of the E-Bus														
		Install and Operate the E-Vision Engineering Tool														
		Use all features of the E-Vision Engineering System														
		Wire a W7750A/B controller for a specific application														
		Understand the purpose and function of W7750A/B controller Hardware/Firmware																			
		Perform Commissioning and Basic Configuration functions using the E-Vision Software																			
		Understand functionally the purpose of the W7750A/B Controller physical input and 

		outputs and to be able to work with them												


Topics:		XL5000 System Block Diagram including the Zone Manager and satellite processors																	
		E-Vision Software Configuration/Installation/Operation												
		W7750A/B Controller Functional Hardware/Firmware													
		W7750A/B Controller Test and Checkout															

Class Type:	Engineering								


System:		XL5000								


Duration:		2.5 days 								


Class Audience:	Technicians installing/servicing down-line satellite Excel 10 									
		W7750A/B Controllers connected to an XBS system and/or maintenance										
		personnel responsible for the same.																

                              
Objectives:	Upon completion of the course the student will be able to:											


  		Identify functionally critical components of a connected E-Bus												
		Understand the purpose and function of the E-Bus																												
		Wire a W7750A/B controller for a specific application														
		Understand the purpose and function of W7750A/B controller Hardware/Firmware																
		Configure the A/B Controllers using the available options																		
		Perform Commissioning and Testing after each given set of configuration options																			
		Understand functionally the purpose of the W7750A/B Controller physical input and 

		outputs and to be able to work with them																	


Topics:		XL5000 System Block Diagram including the Zone Manager and satellite processors																													
		W7750A/B Controller Functional Hardware/Firmware															
		W7750A/B Configuration Options																		
		Testing of the W7750A/B Configuration Options																
		W7750A/B Controller Test and Checkout																	

Class Type:	Engineering								


System:		XL5000								


Duration:		3.0 days 								


Class Audience:	Technicians installing/servicing down-line satellite Excel 10 									
		W7751B/D/F/H Controllers connected to an XBS system and/or 										
		maintenance personnel responsible for the same.																

                              
Objectives:	Upon completion of the course the student will be able to:											


  		Identify functionally critical components of a connected E-Bus													
		Understand the purpose and function of the E-Bus																												
		Wire a W7751B/D/F/H controller for a specific application															
		Understand the purpose and function of W7751B/D/F/H controller Hardware/Firmware																				
		Configure the W7751B/D/F/H Controllers using all available options																		
		Perform Commissioning and Testing after each given set of configuration options																			
		Understand functionally the purpose of the W7751B/D/F/H Controller physical input 

		and outputs and to be able to work with them																


Topics:		XL5000 System Block Diagram including the Zone Manager and satellite processors																													
		W7751B/D/F/H Controller Functional Hardware/Firmware																	
		W7751B/D/F/H Configuration Options																				
		Testing of the Configuration Options for W7751B/D/F/H Controllers															
		W7751B/D/F/H Controller Test and Checkout														

Class Type:	Engineering								


System:		XL5000								


Duration:		3.0 days 								


Class Audience:	Technicians installing/servicing down-line satellite Excel 10 									
		Ancillary* Controllers connected to an XBS system and/or 										
		maintenance personnel responsible for the same.																

                              
Objectives:	Upon completion of the course the student will be able to:											


  		Identify functionally critical components of a connected E-Bus													
		Understand the purpose and function of the E-Bus																												
		Wire a W7751B/D/F/H controller for a specific application															
		Understand the purpose and function of Excel 10 Ancillary* Controller Hardware/Firmware																				
		Configure the Excel 10 Ancillary* Controllers using all available options																				
		Perform Commissioning and Testing after each given set of configuration options																			
		Understand functionally the purpose of the Excel 10 Ancillary* Controller physical 

		input and outputs and to be able to work with them																			


Topics:		XL5000 System Block Diagram including the Zone Manager and satellite processors																													
		Excel 10 Ancillary* Controller Functional Hardware/Firmware																	
		Excel 10 Ancillary* Controller Configuration Options																				
		Testing of the Configuration Options for Excel 10 Ancillary* Controllers																						
		Excel 10 Ancillary* Controller Test and Checkout															



* Excel 10 Ancillary controllers include Fan Coil Unit, Unit Ventilator, 														
Remote I/O and Digital Display Wall Module Controllers.																		

Class Type:	Engineering								


System:		XL5000 and XBS-i Central Systems								


Duration:		10 Days / 10 Hour Days 								


Class Audience:	Honeywell Systems Engineers, Programmers, Electricians,									
		electronic systems specialists, and maintenance persons 									
		responsible for electrical/electronic installation/maintenance of 								
		XL5000/XBS-i systems or subsystems at customer sites, Honeywell 									
		Authorized System Distributor Installation Personnel, and 										
		Honeywell Systems Technicians for XBS or other systems and 										
		Programmers/analysts familiar with PC Hardware and Application 									
		programs, and some version of Windows.																

                              																																													
Objectives:	Upon completion of the course the student will be able to:											


  		Define all major networking concepts, terms and definitions														
		Will be able to work with a PC of any description with ease and	confidence																					
		Hardwire at least one hardware configuration for Windows NT														
		Install Windows NT Sever and Windows NT Workstation software successfully																				
		Perform all configuration functions available through the Control Panel																					
		Perform all diagnostic and trouble shooting functions															
		Perform all Windows Registry Functions																	
		Install and configure any Windows applications for running over the network																				
		Install and configure all XL5000 and XBS-i applications over the network																				
		Perform all maintenance functions such as backup/restore for the Windows NT 

		network system																					


Topics:		Network Concepts and terminology										
		Network hardware and wiring													
		Hardware compatibility problems													
		Network software installation and configuration												
		Network Systems Operating Procedures													
		Connectivity as related to Honeywell Automation Systems									
		Application Programming																				
		Honeywell systems installation and configuration															
		Network systems trouble shooting																		
		Honeywell systems trouble shooting																		
		Honeywell SRB's for running Excel 5000 and XBS-i System under Network Operating Systems